The 10 Scariest Things About Car Key Button Repair

Car Key Button Repair

A broken car key button is frustrating. It is possible to contact an emergency locksmith service 24 hours a day to assistance or to purchase a new remote.

You could be able to save money by repairing your old key fob instead of replacing it. This is especially true if the issue is caused by the worn-out switch or defective contact.

Battery

If your key fob's buttons do not respond when you pressing them, this could be a sign that the battery is dead or is about to reach the end of life. Fortunately replacing the battery is an easy task that can be completed on your own instead of hiring a locksmith or dealer to do it for you.

First, locate the battery compartment. It is typically located on the back of the key fob and could be hidden behind an open cover that slides out or an access point that opens when you push the button. When the compartment is open, look for the small button-cell battery. This is typically shaped like coins and has an minus and plus sign. Remove the battery that is old, and replace it with a new one. Check that the plus and the minus symbols are properly aligned.

Once the battery is installed close the compartment and snap the two parts of the key fob. Before closing the door make sure to align and snap the pieces into the correct position. To test whether the buttons function properly Press any of them.

If the remote key fob repairs keyfob isn't working after replacing the battery, there could be other problems that require a different form of repair. Dropping the device in a puddle could cause it to stop functioning. Or, it could be suffering from an electrical issue within the device or may need to be deprogrammed by an expert or locksmith. Find out if the problem is with your key fob applying these other typical automotive troubleshooting methods.

Switches

There are many kinds of switches used in the car keys repairs key fob dependent on the year and make. The older style key is equipped with an embedded chip that can be seen inside the case. The newer keys work by sending signals to your car. The keys' buttons can be worn out or damaged through normal use, regardless of the model. They can become difficult to press or not responsive. If you press the button too hard it could cause more damage. It could also stop the key from working in the future.

If your key doesn't seem to be working, first try changing the battery. If that doesn't help it may be necessary to clean your key fob and adjust the switches. These tiny electronic switches are more prone than the larger parts of the key to break since they are constantly jostled.

The switches are rubber-like, and they're coated with an electrically conducting film that is prone to wear out over time. They're fortunately tiny and cheap to replace. The old ones are soldered to the circuit board so you will need to carefully remove them without damaging anything else. You can then solder the new ones in and then reassemble your fob.

Do not use your car key fob for more than a couple of hours at a time, and don't leave it out in the open. If you don't use your key, store it in a secure place.

If you've tried cleaning your key fob and replacing the battery, but the problem persists it's time to think about hiring a locksmith. A professional locksmith will test the frequency of your key fob repair service to determine whether your vehicle is capable of communicating. They can also open and replace microswitches as well as change cases, and much more.

Outer Case

If the buttons can't move freely in the case, they may be stuck or even break. If changing the battery or cleaning it with a cotton swab and some rubbing alcohol don't resolve the problem, removing the case and inspecting could be required. If the contacts the buttons touch are not suitable for the application or if they're worn, changing them might be the only option.

Certain keys have buttons made of rubber that wear away over time. Rubber buttons can become hard to press because they stretch, and nails can gouge them. In this scenario the key could fail, and it's time to replace the case or the buttons. This repair car key fob involves taking apart your remote, locating the button switches on the board, then heating the solder, and then carefully removing them. The new buttons are then connected to the circuit board. The case is then put back together with the horseshoe key blade piece inserted. The new buttons should be a close fit into the case to prevent them falling out.

Inner Case

Over time the buttons on your key fob could be damaged or stuck due to the constant jolting and accidental pressing. With the help of metallic tape and a hole-punch, you can often quickly solve this issue in the event that your vehicle is not at home and the key fob isn't working and allows you to open the doors, but not to start the engine. This simple fix will enable you to safely get back to your vehicle and finish your trip.