The 10 Scariest Things About Car Key Button Repair

Car Key Button Repair

A broken car key repair mobile car key repair key button can be frustrating. You may need to call an emergency locksmith service that is available 24 hours a day for assistance or purchase a replacement remote.

You could save money by repairing your old key fob instead of replacing it. This is especially true if the issue is caused by the worn-out switch or defective contact.

Battery

If the buttons on your key fob are not responding to your pressing them, it could be a sign that the battery has failed or is close to the end of life. Fortunately replacing the battery is an easy task that you can complete on your own instead of paying a locksmith or dealership to complete the task for you.

First find the battery compartment. The battery compartment is usually located on the back of the key fob and is often hidden behind a cover that opens or a button that opens the access point. Once the compartment is exposed you can see the small button cell battery. It's usually shaped as a coin and has an minus and plus sign. Remove the old battery, and replace it with a new one. Make sure that the plus and symbol are aligned correctly.

Close the compartment and snap together the two parts of your key fob. Before closing the door make sure to align and snap the parts into place. Press any of the buttons to confirm that they function correctly.

If your remote keyfob still isn't working after replacing the battery, it could be other problems that require a different type of repair. Dropping the device in a puddle could cause it to cease functioning. It could also be experiencing an internal electrical problem or may need to be deprogrammed by a dealer or locksmith. Take a look at these other car troubleshooting tips to see if your key fob is suffering from a different issue.

Switches

Based on the year and the model, there are a variety of kinds of switches available that are used in the car keyfob. The older model of key often has a separate chip which is visible inside the case, while the modern keys are more sophisticated and work by sending signals to the car. The buttons on a key can be damaged or worn out due to normal use, regardless of the type. They become difficult to press or unresponsive. If you press the button too hard it can cause further damage. It may also prevent the key from functioning in the future.

If you are unable to get your key to function, try changing the batteries. If this doesn't work, you might need to clean your key's fob or adjust the switches. Since these tiny electronic car key repair near me switches spend a lot of time being moved around they are more prone to wear out than larger parts of your key.

The switches are made of rubber, and they're coated with an electric conductor film that can wear down over time. However, they're tiny and affordable to replace. The old ones are soldered to the circuit board, so you'll need to be careful to remove them without causing damage to other parts. Then, you can solder the new ones into and then reassemble your fob.

Avoid using your car key fob for more than a couple of hours at a stretch and avoid leaving it visible. When you're not using your key, store it in a secure place.

If you've tried cleaning your lock key repair near me fob and replacing the battery, but the issue persists, it may be the right time to seek out the services of a locksmith. A professional locksmith can test the frequency of your key to determine whether your car is able to communicate. They can also open and replace microswitches, alter cases, and much more.

Outer Case

Key fobs spend a lot of time jostled around, and if the buttons aren't free to move upwards and downwards within the case, they may become stuck or break. If changing the battery or cleaning it with a cotton swab and some rubbing alcohol doesn't fix the issue, taking off the case and checking it out could be required. If the contacts the buttons touch are not a good fit or if they're worn, adjusting them may be the only solution.

Rubber buttons can be worn out over time. The rubber is stretched and nails cut into it, and the buttons become difficult to press. This could cause the key to fail and in this instance it is time for an entirely new case or buttons. This repair involves disassembling the remote, locating the button switches on the circuit board, and then heating the solder before carefully taking them off. New buttons are then attached to the circuit board. The case is then put back together with the horseshoe key blade piece attached. The new buttons must be snugly fitted inside the case to avoid them falling out.

Inner Case

Since your key fob is likely be tossed around and occasionally be pressed by accident, the buttons inside can be damaged or stuck over time. If your key fob isn't working when you are away from home, you can solve the issue quickly using metallic tape and punch holes. This allows you to unlock doors but not start the car. This quick fix could allow you to return safely to your vehicle and complete your trip.